Skip to content

HomeLocations

3D Laser Scanning in New Jersey: As-Built Drawings and Revit Models

We laser scan existing buildings across New Jersey and deliver what the design starts from: as-built drawings in DWG and PDF, a Revit model, or the registered point cloud alone. A house with its drawings or model usually costs $2,000 to $4,500, an office or a commercial floor $3,000 to $9,000, and a large building from $12,000. WeAre Capture is a New Jersey company. Scan-to-BIM services in New Jersey usually begin with a building whose drawings are missing or decades out of date.

What you get

DeliverableFormatTypical use in a New Jersey project
Model of the existing building, in Revit or ArchiCADRVT, IFC or an ArchiCAD fileA renovation, an addition or a fit-out designed in BIM
Floor plans and reflected ceiling plansDWG, PDFThe existing conditions sheets behind a permit set or a lease
Elevations, sections and roof plansDWG, PDFFacades, floor-to-floor heights, stairs and roof framing
Registered point cloudE57, RCP/RCSFor a team that draws or models from the scan itself

The model or the drawings are built against the point cloud, and the quote states how accurate they are as a USIBD Level of Accuracy. What the scanner could not see, behind a finished wall or above a hard ceiling, is taken from existing drawings where they show it, and marked as such. The scan-to-BIM, as-built drawings and 3D laser scanning pages describe each deliverable in full.

Prices in New Jersey

What is orderedTypical price
A single room, a basement or one small floorFrom about $1,000
A house, a townhouse or an apartment$2,000 to $4,500
A house with its facades and the site$2,500 to $5,000
An office, a store or another commercial floor$3,000 to $9,000
A large building, about 40,000 square feet and overFrom $12,000, quoted on its own
Registered point cloud onlyFrom about $1,200 for a house or a floor
Revit model from a point cloud you already have$0.15 to $0.30 per sq ft, from about $800

These are our typical ranges, and a specific building can land outside them. The price is fixed for the project and covers the scan on site and the work built on it. For the price per square foot by building size, see the guides to scan to BIM cost and as-built drawings cost.

Where measured drawings come up under New Jersey's construction code

A renovation in New Jersey goes through the state's Uniform Construction Code, N.J.A.C. 5:23, whose Rehabilitation Subcode, 5:23-6, covers work in existing buildings. The construction permit is issued by the construction official of the town. These are the points where the design team needs the building measured.

SituationWhat the code saysWhat we measure
A project in an existing buildingBy the subcode's own introduction, "work is classified into six categories", and "the categories are repair, renovation, alteration, reconstruction, change of use and additions"The plan of the building as it stands, on which the design team marks the scope
Walls, doors, windows or ceilings are movedThe subcode defines an alteration as, among other things, "the rearrangement of any space by the construction of walls or partitions or by a change in ceiling height, the addition or elimination of any door or window"The partitions, openings and ceiling heights before the change
A reconstruction project"For reconstruction work in an existing structure, the work area shall be clearly delineated on the plans"The whole floor or tenancy, so the work area is drawn on a measured base
A change of use"It shall be unlawful to change the use of any structure or portion thereof without the prior application for and issuance of a certificate of occupancy"The current layout: rooms, exit paths, stair and door widths

Our drawings are the measured base your architect or engineer draws the permit set on; with few exceptions, such as a homeowner's own plans for a single-family house, the plans submitted carry "the seal and signature of the registered architect or licensed engineer who prepared the plans". If a land surveyor has set control on the site, the scan is registered to it and the drawings come out in the surveyor's coordinates.

Buildings we scan in New Jersey

  • Houses. Colonials, capes and split-levels with additions from three different decades, where the addition never lined up with the original floor. The basement, every floor and the attic are scanned so the floor levels agree in section, and the facades when the exterior is in scope.
  • Row houses and brownstones in Hoboken and downtown Jersey City: three or four floors, a rear extension added later, and neighbors sharing both side walls.
  • Mills and factories turned into apartments or offices. Heavy timber or cast iron columns on a grid that is never quite regular, and floors that slope toward the old drains.
  • Warehouses and distribution buildings. Long clear spans, racking, dock doors and the roof structure above them, often ordered as a point cloud, with a model only of the areas that change.
  • Offices, laboratories and medical space. The floor, the ceiling with what hangs in it, and the mechanical rooms, for a fit-out or a change of tenant.
  • Stores and restaurants. The storefront, the dining room, the kitchen and the back of house, with the equipment where it stands.

Revit modeling and BIM services in New Jersey

When the team works in Revit, the scan becomes an as-built model of the architecture and the structure, usually at LOD 300, with the mechanical, electrical and plumbing systems added where they are exposed and in scope. The model is delivered in the Revit version your office uses, with the point cloud linked on shared coordinates so the two stay aligned. If the building has already been scanned, by your own crew or by a surveyor, we model from that point cloud; the point cloud modeling page lists what to send. The guide to LOD 200 vs LOD 300 shows what each level looks like on real elements.

How a project runs

  1. Send the address, the rough square footage and the deliverable: a Revit model with its LOD, a list of sheets, or the cloud alone.
  2. The fixed quote comes back within one business day.
  3. The scan takes about a day for a house or a single commercial floor. Tenants and staff keep working around the tripod.
  4. The registered point cloud is usually ready within a few days. A house is usually modeled or drawn in two to three weeks, a commercial floor in two to four, a whole building in four to six.

Where we work

All 21 counties, from Bergen, Hudson, Essex and Morris in the north through Union, Middlesex and Mercer to Camden, Atlantic and Cape May in the south, including Jersey City, Newark, Hoboken, Paterson, Elizabeth, Edison, Princeton, Morristown and the towns along the Shore. Across the Hudson, New York City has its own page.

Frequently asked questions about laser scanning in New Jersey

How much does 3D laser scanning cost in New Jersey?

With drawings or a model, a house, a townhouse or an apartment usually costs $2,000 to $4,500, an office or a commercial floor $3,000 to $9,000, and a large building from $12,000. A single room or one small floor starts at about $1,000, and a registered point cloud alone at about $1,200 for a house or a floor.

Do you offer Revit modeling in New Jersey?

Yes. The usual order is a scan with a Revit model of the existing building at LOD 300. A model from a point cloud you already have costs $0.15 to $0.30 per square foot, from about $800.

Who applies for the construction permit?

The owner, or the owner's architect, engineer or contractor acting for them. They get the measured drawings of the building from us and prepare the permit plans on them.

Can the drawings be used for a change of use or a certificate of occupancy?

Yes: your architect or engineer draws the application on them. New Jersey's code makes it unlawful to change the use of a structure "without the prior application for and issuance of a certificate of occupancy", and the plans for that application begin with the layout as measured.

Can you scan a warehouse or an office while it is working?

Yes. The warehouse keeps shipping and the office keeps working: aisles are scanned between forklift runs, and an office floor by floor around the people in it. Clear floor along the walls gives a more complete plan.

How soon can you be on site in New Jersey?

Often within days of the order. The quote itself takes one business day, and the scan date is set by when the building can be entered.

Which parts of New Jersey do you cover?

The whole state, all 21 counties, and New York City across the river.

Sources

Ready when your site is.