3D Scanning for Reverse Engineering: Cost per Part in 2026
3D scanning for reverse engineering usually costs about $1,000 for a simple part, scanned and rebuilt as a CAD model in STEP, $1,500 to $2,500 for a part with free-form surfaces or a set of two or three simple parts, and $3,000 to $6,000 for a large part such as a body panel or a forming tool. A scan alone, delivered as a mesh in STL without a CAD model, usually comes in under $1,000 for a small object, and whole machines and vehicles are quoted on their own. The price follows three things: the size of the part, how much of it is free-form surface rather than simple geometry, and what the model is for. Below is our 2026 pricing for reverse engineering by type of part, what the price includes, a worked example, and what to send for a quote.
How much does 3D scanning for reverse engineering cost in 2026
Our reverse engineering is priced per project. The price covers the 3D scan of the part and the CAD model rebuilt from it.
| What is scanned and modeled | Typical price |
|---|---|
| A small object scanned to a mesh (STL), without a CAD model | Usually under $1,000 |
| A simple machined part, scanned and modeled in STEP | From about $1,000 |
| A part with free-form surfaces, or two or three simple parts | $1,500 to $2,500 |
| A large part: a body panel, a fender, a forming tool, up to about 1.5 m | $3,000 to $6,000 |
| A whole machine, a vehicle or an assembly | Quoted on its own, usually from $8,000 |
These are our typical ranges, and a specific part can land outside them. The quote is a fixed price for the project, with the scan and the modeling priced together.
What the price includes
The price covers the scan of the part, in the shop or wherever the part sits, and the work built on it:
- The scanned surface as a mesh in STL, which on its own is enough to 3D print a copy, check wear against a newer part or fit a component around it.
- The CAD model, rebuilt as a solid in STEP, with native formats on request.
- A check of the model against the scan before delivery, with a list of the features that were restored to a design size and the features that follow the scan as measured.
- Drawings in DWG and PDF, added when the part is going to be made again in a machine shop.
The reverse engineering services page describes the scanning and the modeling in detail, and 3D scanning for parts and objects covers scans without a CAD model.
Mesh, CAD model or drawings: what to order
The deliverable decides most of the price, because the scan of a part is usually the shorter half of the job and the modeling is the longer one.
| Deliverable | What it is | Good for | What it does to the price |
|---|---|---|---|
| Mesh (STL) | The scanned surface as a network of triangles | 3D printing a copy, checking wear, fitting a part around it | The lowest; a small object usually under $1,000 |
| CAD model (STEP) | A solid model with flat faces, round bores and standard sizes restored | Machining, modifying, sending to a shop for a quote | From about $1,000 per part |
| Drawings (DWG, PDF) | Dimensioned 2D sheets of the model | Making the part again from paper | Added to the CAD model, listed in the quote |
A mesh copies one part exactly as it is, wear and damage included. A CAD model is the part as it was designed: a bore that measures 25.06 mm on a worn part was drawn at 25 mm, and the model says so. The guide to how to scan an object into CAD shows the steps from the scanner to the STEP file, and scan-to-CAD vs product design explains when a part needs a copy and when it needs a redesign.
What moves the price
The size of the part. A part that fits on a bench is scanned in one session. A fender, a tool or a machine frame takes more passes and more targets, and a part over a metre or two is often scanned where it stands.
Free-form surfaces. A bracket made of flat faces, holes and fillets is quick to rebuild, because each feature has a simple description. A blade, a moulded grip or a body panel has surfaces that have to be fitted to the scan one patch at a time, and that is where the modeling time goes.
What the model is for. A replacement that has to mate with an existing assembly keeps the measured positions of its interfaces. A part being redesigned gets a clean model with the wear taken out. A copy for 3D printing may need nothing beyond the mesh. Which features are restored and which are copied is agreed before the modeling starts.
The number of parts. Two or three simple parts in one job cost less than the same parts ordered one at a time, because the visit and the setup are shared.
The condition of the part. A worn, cracked or broken part is still scanned as it is, and the missing or damaged areas are rebuilt from symmetry, from mating parts or from the measurements of an unworn sample when there is one.
Drawings. A dimensioned drawing set for manufacturing is extra drafting time on top of the model, and the quote lists it on its own line.
Worked example: a cast pump housing
Take a cast pump housing about 30 cm across, out of production, with no drawing. The outside is a free-form casting, while the flanges, the bolt pattern and the bores are simple machined features that have to mate with the pump and the piping.
- The housing is scanned in one session, usually in a day, and the mesh follows within a few days.
- The machined features are rebuilt at their design sizes, the flange faces flat and square, the bolt holes on their nominal circle, and the cast outside is fitted to the scan.
- Mixed geometry like this sits in the $1,500 to $2,500 range for the scan and the STEP model.
- A drawing set for the machine shop is added on top when the housing is going to be cast and machined again.
The model usually follows in one to two weeks. If the inside of the housing matters, the volute and the internal passages are handled as described in the next section.
What a surface scan does not capture
A scanner records the surfaces its light reaches. Deep bores, internal passages and the inside of a closed casting are not captured from the outside. Those features are measured at the openings, documented from a sectioned part or taken from drawings where they exist, and the model marks which features were scanned and which were not. CT scanning, which sees inside a part, is not part of our service; the guide to CT scanning for internal features explains when a job needs it.
What the quote needs
The fixed quote arrives within one business day of your sending photographs of the part from several sides with a ruler or a tape in the frame, its approximate size and material, what the model is for, how many parts there are, whether drawings are needed, and any mating parts that the model has to fit. Say where the part is, and whether there is a deadline. The reverse engineering quote checklist lists what to send, and the guide to reverse engineering discontinued spare parts covers the most common case. A single part is usually scanned in a day, the mesh usually follows within a few days, and the CAD model in one to two weeks. We scan in all 50 states.
FAQ
How much does 3D scanning for reverse engineering cost?
A simple part, scanned and modeled in STEP, starts at about $1,000. A part with free-form surfaces, or two or three simple parts, usually runs $1,500 to $2,500, and a large part such as a body panel or a forming tool $3,000 to $6,000. Whole machines and vehicles are quoted on their own.
How much does it cost to 3D scan a part without a CAD model?
A small object scanned to a mesh in STL usually comes in under $1,000. Larger parts are quoted on their size and surface.
Is reverse engineering priced per part or per hour?
Per project. The quote is a fixed price for the scan and the model together, set by the size of the part, its surfaces and what the model is for.
Which file formats do you deliver?
STL for the scanned mesh, STEP for the CAD model, DWG and PDF for drawings, and native CAD formats on request.
How long does reverse engineering take?
A single part is usually scanned in a day. The mesh usually follows within a few days and the CAD model in one to two weeks, depending on how many features have to be rebuilt.
Can you reverse engineer a broken or worn part?
Yes. The part is scanned as it is, and the damaged or worn areas are rebuilt from symmetry, from mating parts or from an unworn sample, with the restored features listed in the model’s report.
Can you capture internal passages?
A surface scan captures what the light reaches. Internal passages are measured at the openings, documented from a sectioned part or taken from existing drawings. CT scanning is not offered.
Sources
- ISO 10303 (STEP), list of parts: Part 21, the clear text encoding of the exchange structure used for STEP files.